Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Content layer
id2057153239
Content column
id2057153250
Content block
id2057153238

On this page

Table of Contents
maxLevel4

Content block
id2057153240

An Accident Scenarios Table allows you to define Accident Scenarios as a combination of Malfunctioning Behaviors and Operational Situations. The sections below explain how to create Accident Scenarios and assign the controllability level, Malfunctioning Behavior and Operational Situations.

An example of an Accident Scenarios Table.

Creating Accident Scenarios Table

You can create an Accident Scenarios Table as described below.


To create an Accident Scenarios Table


  1. In the Containment tree, select the element that you want to be the owner of the table.
  2. Do one of the following:
    • In the main menu, go to Diagrams > Create Diagram, then select Accident Scenarios Table in the open dialog.
    • In the Containment tree, right-click the owner of the table, select Create Diagram and select Accident Scenarios Table in the open dialog.



  3. When the table is created, type the name of the table and press Enter.


After following the above steps, an Accident Scenarios Table is created. The scope and element type of the table are already specified for you.


Creating Accident Scenarios

There are two ways to create an Accident Scenario: you can do it right in an Accident Scenarios Table or in the Containment tree.


To create an Accident Scenario in the Containment tree


  1. In the Containment tree, right-click the owner of a new element and select Create Element.
  2. In the open window, select Accident Scenario.



  3. When an Accident Scenario is created, type the name of the element and press Enter.


When you create an Accident Scenario in the model browser, it is automatically added to an Accident Scenarios Table if it exists.


To create an Accident Scenario in an Accident Scenarios Table


  1. In an Accident Scenarios Table, select a table row.
  2. Do one of the following:
    • In the table toolbar, click  to create an element of the same level as the one you have selected.
    • In the table toolbar, click  to create an element nested under the selected element.

  3. Type the name of the new element and press Enter.


When you create an Accident Scenario and add it to an Accident Scenarios Table, you need to define the element as described in the section below.


Defining Accident Scenarios

After creating an Accident Scenario, you need to define its controllability level which allows you to estimate the probability of avoiding the specified harm or damage. Also, you have to assign a Malfunctioning Behavior and Operational Situations to the Accident Scenario. 


To define a Controllability level


  1. In an Accident Scenarios Table, double-click the cell of the Controllability column and select the desired controllability level from the list.



  2. Double-click the cell of the Justification of Controllability column and write the justification to explain the selected controllability level.


Assigning a Malfunctioning Behavior


  1. In an Accident Scenarios Table, double-click the cell of the Malfunctioning Behavior column and click .
  2. On the left side of the Select Elements dialog, open the List tab.
  3. Select the Malfunctioning Behavior you want to assign and click OK.


Assigning Operational Situations


  1. In an Accident Scenarios Table, double-click the cell of the Operational Situation column and click .
  2. On the left side of the Select Elements dialog, open the List tab.
  3. Double-click the Operational Situations you want to assign. The elements should be added to the selected elements area on the right side of the dialog.



  4. Click OK.


Tip
titleUse filters to find elements quicker

When you assign a Malfunctioning Behavior or Operational Situations, use a filter after step 2 to find elements quicker:

  1. In the Select Elements dialog, click next to the Filter by ISO properties box.
  2. In the Select Properties dialog, click the Value box of a property and select the desired property value from the list.



  3. Click OK.

Now the List tab displays the elements with the selected property value.