You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 22 Next »

This page shows the example to install and configure Teamwork Cloud (TWCloud) 19.0 Standard Edition on Centos 7.x, deployed on a single server. It also shows the configuration in which both the Teamwork Cloud node as well as the underlying Cassandra node are installed on the same server.

TWCloud installation and configuration on Centos 7.x on a single server.

Recommended system requirements

System requirements are dictated by the intended deployment, taking into account the overall load which the environment will experience

  • Number of concurrent users
  • Level of activity (commits) per day
  • Overall number and size of the projects stored in Teamwork Cloud.

From a hardware perspective, the database (Cassandra) can be located on the same server as Teamwork Cloud, or separated into its own server.  Storage requirements apply only to the node where the database is located.

Ideally, the node hosting Cassandra should be a physical node, since virtualization will introduce a performance degradation.  Nodes running Cassandra should have DAS SSD drives (direct attached).  Best performance will be obtained using NVMe drives.  Presently, there are hardware limitation on the size of the NVMe drives as well as the number of NVMe drives which can be installed on a single machine.  Therefore, if the expected number and size of projects is significant, SAS SSD backed by a high speed caching controller may be a more suitable choice.  For ease of maintenance and reduction of risk, we recommend that the volumes reside on RAID-1 or RAID-10.  If RAID is not used, the failure of a drive will result in a downed node, impacting the enterprise.  By opting to deploy on RAID volumes, a drive failure will not affect the application and will allow replacement of a drive with zero down time. 

Nodes hosting Teamwork Cloud nodes can be virtualized without any issues, provided the host is not oversubscribed on its resources.

Nodes containing both Teamwork Cloud and Cassandra

  • 96 -128 GB ECC RAM
  • >=16 processor threads (such as E5-1660)
  • >1TB SSD DAS storage

Nodes containing only Cassandra

  • 48 - 64 GB ECC RAM
  • >=8 processor threads (such as E5-1620)
  • >1TB SSD DAS storage

Nodes containing only Teamwork Cloud

  • 48 - 64 GB ECC RAM
  • >=8 processor threads (such as E5-1620)
  • >250GB storage


Multi-Node Clusters

Recommended minimum sizing stated above applies to each node in a multi-node cluster

SAN Storage

SAN Storage should not be used on Cassandra nodes for data or commitlog volumes. This will result in severe performance degradation. There is absolutely no amount of SAN tuning and OS tuning which will mitigate this.


Minimum server system requirements

  • 8 Processor Cores - i.e. Quad Core Hyper-threaded CPU (such as Intel E3-1230 or faster).
  • 32 GB RAM (Motherboard with an ECC RAM is always preferred on any critical database server).
  • Linux (RedHat/CentOS 7), 64 bit.  Scripts need to be modified slightly for Centos 6.6 - 6.9 due to different system daemon and firewall configuration.

Please read the article for additional server recommendations for capacity and performance from the following link:

https://docs.datastax.com/en/dse-planning/doc/planning/planningHardware.html

If you use SATA drives and not SSD's, we recommend using a caching controller with BBU, configured for write back. In this configuration (single node Cassandra), we recommend using RAID - the aforementioned link is referring to multi-node Cassandra deployments where native Cassandra replication is in place, which is not the case in this single node instance.

In order to install a full working environment, the following are required.

  • Oracle Java (Java Hotspot) 1.8.0_202
  • A FlexNet License Server
  • Cassandra 3.11.x
  • Teamwork Cloud

Preparing the operating system

Partitioning the drives

Prior to installing Cassandra, it is important to understand how Cassandra utilizes disk space in order to properly configure the host server.

Disk space depends on usage, so it's important to understand the mechanism. The database writes data to disk when appending data to the commitlog for durability and when flushing memtables to SSTable data files for persistent storage. The commit log has a different access pattern (read/writes ratio) than the pattern for accessing data from SSTables. This is more important for spinning disks than for SSDs.

SSTables are periodically compacted. Compaction improves performance by merging and rewriting data and discarding old data. However, depending on the type of compaction and size of the compactions, during compaction disk utilization and data directory volume temporarily increases. For this reason, be sure to leave an adequate amount of free disk space available on a node.

Cassandra data and commit logs should not, under any circumstances, be placed on the drive where the operating system is installed.  Ideally, a server would have 3-4 drives or partitions.  The root partition,  /, the OS partition, can be used as the target for the application.  A /data partition should have adequate amounts of storage to accommodate your data.  A /logs partition would hold your commit logs (and unless SSD, should be on a different physical disk than the data partition), and a /backup partition would be allocated for backups.

Please refer to http://cassandra.apache.org/doc/latest/operating/hardware.html for explanations on hardware selection.

In order to achieve adequate performance, separate partitions must be created, ideally on separate drives, to avoid i/o contention. We recommend 3 separate block devices (disks). The first block device will contain the operating system as well as a mount for the programs (/opt/local). The second block device (preferably SSD) will contain a mount point at /data - this is the device which must have high storage capacity for all of the data. The third block device will contain a mount point at /logs - this device should preferably be SSD, but does not need to be of high capacity, since it will only store the commit logs, which are by default limited to 8GB (if using SSD, this can be a partition on the same block device as the data partition). All partitions should be formatted using the XFS file system, and there must not be a swap partition.  The /backup partition can be a mount on a shared storage device, and shoud not be on the same physical drive as the /data partition.

The following is an example of the contents of  /etc/fstab after partitioning, where the partitions were created using
 LVM (without a mount for the /backup partition)

fstab
#
# /etc/fstab
# Created by anaconda on Tue May  2 16:31:05 2017
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
/dev/mapper/cl_twccentos7-root /                       xfs     defaults        0 0
/dev/mapper/cl_twccentos7-data /data                   xfs     defaults        0 0
/dev/mapper/cl_twccentos7-logs /logs                   xfs     defaults        0 0
/dev/mapper/cl_twccentos7-opt_local /opt/local         xfs     defaults        0 0


  • Disk 1 will contain the following partitions:  /opt/local (40GB) and / (rest of the drive capacity)
  • Disk 2 (the disk with the highest capacity) will contain the /data partition - as a minimum, we recommend 250GB.  Due to the way compactions are handled by Cassandra, in a worst case scenario up to 50% of headroom may be needed.
  • Disk 3 will contain the /logs partition (at least 10 GB)
  • You should also create an additional mount for backups.  Unlike the data and commitlogs partitions, which should be on SSD storage, this mount can be of any type (including centralized storage such as a SAN or NAS).  It should have at least the same capacity as the /data partition.

The aforementioned partitioning scheme is an example. Internal security protocols in your organization may dictate that other directories not be located in the main partition. During the installation, all applications will be installed in /opt/local. Cassandra will install by default in /var/lib. Application logs will be written to /home/twcloud.

Installing Oracle Java (Option 1)

From the Java version list, please check that the recommended Oracle JVM version is compatible with the TWCloud version you are using.  In order to consolidate all of the installed applications in a single location, we will be installing under /opt/local/java. To facilitate deployment, you may deploy using the associated script (install_java_202.sh).  Oracle no longer allows direct download of their JDK, so it must be downloaded offline and placed in the same location as the install scripts.  The installation script extracts it into the proper location, invokes the alternatives command to point the system to this instance (you may need to select it when prompted), and creates entries in /etc/environment. Upon completing the installation, issue the following command:

  
          java -version


You should receive output such as the following:

          java version "1.8.0_202"
          Java(TM) SE Runtime Environment (build 1.8.0_202-b08)
          Java HotSpot(TM) 64-Bit Server VM (build 25.202-b08, mixed mode)


If properly installed, you will see Java identified as Java HotSpot(TM)


install_java_202.sh
#!/bin/bash
echo "=========================================="
echo "Installing Oracle Java 1.8.0_202"
echo "=========================================="
echo ""
echo "  Oracle Java can no longer be downloaded directly due to new authentication requirements"
echo ""
echo "  After manually downloading jdk-8u202-linux-x64.tar.gz, copy it to this directory"
echo ""
echo "  Latest version is avilable from https://www.oracle.com/technetwork/java/javase/downloads/jdk8-downloads-2133151.html"
echo ""
echo "  Archive downloads available from http://www.oracle.com/technetwork/java/javase/downloads/java-archive-javase8-2177648.html"
echo ""
read -p -"Press any key to continue, Ctl-C to exit ...: " -n1 -s
echo ""
echo "==========================================" 
sudo mkdir -p /opt/local/java
sudo tar xzf jdk-8u202-linux-x64.tar.gz -C /opt/local/java
cd /opt/local/java/jdk1.8.0_202/
sudo alternatives --install /usr/bin/java java /opt/local/java/jdk1.8.0_202/bin/java 2
sudo alternatives --config java
sudo alternatives --install /usr/bin/jar jar /opt/local/java/jdk1.8.0_202/bin/jar 2
sudo alternatives --install /usr/bin/javac javac /opt/local/java/jdk1.8.0_202/bin/javac 2
sudo alternatives --set jar /opt/local/java/jdk1.8.0_202/bin/jar
sudo alternatives --set javac /opt/local/java/jdk1.8.0_202/bin/javac
sudo echo 'JAVA_HOME=/opt/local/java/jdk1.8.0_202' > /etc/environment
sudo chown -R root:root /opt/local/java/jdk1.8.0_202

Installing OpenJDK 8 (Option 2)

Teamwork Cloud can also operate with OpenJDK.  You can install OpenJDK using the script below below.


install_openjdk8.sh
#!/bin/bash
echo "Install OpenJDK 1.8"
yum -y install java-1.8.0-openjdk  


Installing the FlexNet server (lmadmin)

A FlexNet license server is required for Teamwork Cloud to operate.  It can be installed on the same system, or on a separate machine. The automated deployment script (install_flex_centos7.sh) downloads all required components, deploys the server, creates the systemctl service entry to control it, and creates the necessary firewalld rules to allow the required traffic. The firewall rules are created for both the internal and public zones, and the script may require modification depending on which zone the interface is located. Additionally, if firewalld is not running when the installation script is executed, the rules will not be created. The script creates a user, lmadmin, which runs the lmadmin service. The FlexNet server requires the Redhat LSB core files as well as the ld-linux library in order to execute. The script is configured for Centos 7, but can be modified for a different version.  In order to identify which LSB Core library is required, the following command can be issued:  

     sudo yum provides /lib/ld-lsb.so.3

The application should be installed in /opt/local/FNPLicenseServerManager (the installer's default location is /opt/FNPLicenseServerManager - so make sure that you change the location when prompted). All other default values presented by the installer should be accepted.

  • After the lmadmin server has been installed it can be started by issuing the command:
    sudo systemctl start lmadmin


  • To check if the service is running, issue the following command
    sudo systemctl status lmadmin


  • If the service failed to start, it is often because the built-in web server cannot resolve the host name.  To check if this is the case, issue the following commands:
    cd /opt/local/FNPLicenseServerManager/logs
    tail web.log

You will see output similar to the following:

[Tue May 02 18:43:27 2017] [alert] (EAI 2)Name or service not known:
mod_unique_id: unable to find IPv4 address of "yourhostname"
Configuration Failed

Where yourhostname is the name of the host.  If this is the case, you will need to edit the /etc/hosts file and add an entry so the web server can resolve the host. The line will be in a format similar to the following:

         192.168.130.10  yourhostname


install_flex_centos7.sh
#!/bin/bash
echo "==============="
echo "Installing wget"
echo "==============="
yum install -y wget
echo "=================="
echo "Installing lmadmin"
echo "=================="
echo "Creating temporary directory for install anywhere"
IATEMPDIR=$(pwd)/_tmp
export IAEMPDIR
mkdir $IATEMPDIR
getent group lmadmin >/dev/null || groupadd -r lmadmin
getent passwd lmadmin >/dev/null || useradd -d /home/lmadmin -g lmadmin -m -r lmadmin
yum install -y ld-linux.so.2
LSB=$(yum provides /lib/ld-lsb.so.3 | grep lsb-core | tail -1 | cut -f 1 -d ' ')
yum install -y $LSB
echo "lmadmin ALL=(ALL) NOPASSWD:ALL " >> /etc/sudoers
# If Web GUI to Flex licensing is not a must - lmgrd can be used, can be placed in rc.local to startup on boot
# usage - ./lmgrd -c PATH_TO_KEY_FILE -l PATH_TO_LOG_FILE
# RW rights needed to both files
echo "==========================================================="
echo "Getting Linux 32-bit IPv6 version 11.14 "
echo "==========================================================="
wget http://d1g91r27pzl568.cloudfront.net/Cameo_daemon/FlexNet_11_14/ipv6/linux/lnx_32/cameo
chmod +x cameo
echo "========================================"
echo "Getting Linux 32-bit lmgrd version 11.16"
echo "========================================"
wget https://d1oqhepk9od1tu.cloudfront.net/Flex_License_Server_Utilities/v11.16.4/linux32/lmgrd
chmod +x lmgrd
echo "======================================"
echo "Making flex log file named FlexLog.log"
echo "======================================"
touch FlexLog.log
chmod 664 FlexLog.log
echo "=========================================="
echo "Getting Linux 32-bit lmadmin version 11.16"
echo "=========================================="
wget https://d1oqhepk9od1tu.cloudfront.net/Flex_License_Server_Utilities/v11.16.4/linux32/lmadmin-i86_lsb-11_16_4_0.bin
chmod +x lmadmin-i86_lsb-11_16_4_0.bin
echo "========================================="
echo "Executing lmadmin version 11.16 installer"
echo "IMPORTANT: Install into directory /opt/local/FNPLicenseServerManager"
echo ""
echo " Note:  Accept all defaults for script to work properly!!!"
echo ""
read -p -"Press any key to continue ...: " -n1 -s
echo "=========================================="
./lmadmin-i86_lsb-11_16_4_0.bin -DUSER_INSTALL_DIR=/opt/local/FNPLicenseServerManager
mkdir -p /opt/local/FNPLicenseServerManager/licenses/cameo/
cp cameo /opt/local/FNPLicenseServerManager/cameo
mv cameo /opt/local/FNPLicenseServerManager/licenses/cameo/cameo
mv lmgrd /opt/local/FNPLicenseServerManager/lmgrd
mv FlexLog.log /opt/local/FNPLicenseServerManager/FlexLog.log
chown -R lmadmin:lmadmin /opt/local/FNPLicenseServerManager/
chmod +x /opt/local/FNPLicenseServerManager/lib*
cp /opt/local/FNPLicenseServerManager/lib* /usr/lib/
echo "======================"
echo "Opening firewall ports"
echo "======================"
FWZONE=$(firewall-cmd --get-default-zone)
cat <<EOF > /etc/firewalld/services/lmadmin.xml
<?xml version="1.0" encoding="utf-8"?>
<service version="1.0">
    <short>lmadmin</short>
    <description>lmadmin</description>
    <port port="8090" protocol="tcp"/>
    <port port="1101" protocol="tcp"/>
</service>
EOF
sleep 30
firewall-cmd --zone=public --remove-port=8090/tcp --permanent &> /dev/null 
firewall-cmd --zone=public --remove-port=1101/tcp --permanent &> /dev/null 
firewall-cmd --zone=public --remove-port=27000-27009/tcp --permanent &> /dev/null 
firewall-cmd --zone=internal --remove-port=8090/tcp --permanent &> /dev/null 
firewall-cmd --zone=internal --remove-port=1101/tcp --permanent &> /dev/null 
firewall-cmd --zone=internal --remove-port=27000-27009/tcp --permanent &> /dev/null 
firewall-cmd --zone=$FWZONE --add-service=lmadmin --permanent
firewall-cmd --reload
IP_ADDRESS=$(ip route get 1 | awk '{print $NF;exit}') 
HOSTNAME=$(hostname)
echo "$IP_ADDRESS     $HOSTNAME" >> /etc/hosts  
echo "=========================================="
echo "Creating systemd service - lmadmin"
echo "=========================================="
echo "[Unit]" > /etc/systemd/system/lmadmin.service
echo "Description=Flexnet License Daemon" >> /etc/systemd/system/lmadmin.service
echo "After=network.target network.service" >> /etc/systemd/system/lmadmin.service
echo "" >> /etc/systemd/system/lmadmin.service
echo "[Service]" >> /etc/systemd/system/lmadmin.service
echo "User=lmadmin" >> /etc/systemd/system/lmadmin.service
echo "WorkingDirectory=/opt/local/FNPLicenseServerManager/" >> /etc/systemd/system/lmadmin.service
echo "ExecStart=/opt/local/FNPLicenseServerManager/lmadmin -allowStopServer yes" >> /etc/systemd/system/lmadmin.service
echo "Restart=always" >> /etc/systemd/system/lmadmin.service
echo "RestartSec=30" >> /etc/systemd/system/lmadmin.service
echo "Type=forking" >> /etc/systemd/system/lmadmin.service
echo "" >> /etc/systemd/system/lmadmin.service
echo "[Install]" >> /etc/systemd/system/lmadmin.service
echo "WantedBy=multi-user.target" >> /etc/systemd/system/lmadmin.service
echo "" >> /etc/systemd/system/lmadmin.service
chown root:root /etc/systemd/system/lmadmin.service
chmod 755 /etc/systemd/system/lmadmin.service
systemctl daemon-reload
systemctl enable lmadmin.service
echo "Removing installanywhere temporary directory"
rm -fr $IATEMPDIR
echo "=========================================="
echo "lmadmin service installation complete"
echo "  usage: systemctl start|stop lmadmin"
echo "==========================================" 

Installing Apache Cassandra 3.11.x


The deployment script for Cassandra removes Datastax Community Edition 2.2.x as well as OpsCenter and the Datastax Agent (which are not compatible with Cassandra 3.x), downloads and installs Cassandra the Cassandra tools from the Apache Software Foundation repository, and creates the necessary firewalld rules to allow proper operation both for a single node or a cluster installation.  To install, execute the installation script (install_cassandra_3_11_centos7.sh).


install_cassandra3_11_centos7.sh
#!/bin/bash
echo "=========================================="
echo "Installing Apache Cassandra 3.11.x"
echo "=========================================="
echo "Removing Datastax Community Edition"
yum remove -y datastax-agent
yum remove -y opscenter
yum remove -y cassandra22-tools
yum remove -y cassandra22
yum remove -y dsc22
rm -f /etc/yum.repos.d/datastax.repo
echo "Creating Apache Cassandra Repository File"
echo "[cassandra]" > /etc/yum.repos.d/cassandra.repo
echo "name=Apache Cassandra" >> /etc/yum.repos.d/cassandra.repo
echo "baseurl=http://www.apache.org/dist/cassandra/redhat/311x/" >> /etc/yum.repos.d/cassandra.repo
echo "gpgcheck=1" >> /etc/yum.repos.d/cassandra.repo
echo "repo_gpgcheck=1" >> /etc/yum.repos.d/cassandra.repo
echo "gpgkey=https://www.apache.org/dist/cassandra/KEYS" >> /etc/yum.repos.d/cassandra.repo
yum install -y epel-release
yum install -y cassandra
yum install -y cassandra-tools
yum install -y jemalloc
chkconfig --add cassandra
chkconfig cassandra on
echo "======================="
echo "Configuring firewall"
echo "======================="
FWZONE=$(firewall-cmd --get-default-zone)
echo "Discovered firewall zone $FWZONE"
cat <<EOF | tee /etc/firewalld/services/cassandra.xml
<?xml version="1.0" encoding="utf-8"?>
<service version="1.0">
    <short>cassandra</short>
    <description>cassandra</description>
    <port port="7000" protocol="tcp"/>
    <port port="7001" protocol="tcp"/>
	<port port="9042" protocol="tcp"/>
	<port port="9160" protocol="tcp"/>
	<port port="9142" protocol="tcp"/>
</service>
EOF
sleep 5
firewall-cmd --zone=$FWZONE --remove-port=7000/tcp --permanent  &> /dev/null
firewall-cmd --zone=$FWZONE --remove-port=7001/tcp --permanent  &> /dev/null
firewall-cmd --zone=$FWZONE --remove-port=7199/tcp --permanent  &> /dev/null
firewall-cmd --zone=$FWZONE --remove-port=9042/tcp --permanent  &> /dev/null
firewall-cmd --zone=$FWZONE --remove-port=9160/tcp --permanent  &> /dev/null
firewall-cmd --zone=$FWZONE --remove-port=9142/tcp --permanent  &> /dev/null
firewall-cmd --zone=$FWZONE --add-service=cassandra --permanent 
firewall-cmd --reload
echo "====================================================="
echo "Changing ownership of data and commit log directories"
echo "====================================================="
mkdir /data &> /dev/null
mkdir /logs &> /dev/null
chown cassandra:cassandra /data &> /dev/null
chown cassandra:cassandra /logs &> /dev/null
echo "====================================================="
echo "Making configuration file changes"
echo "====================================================="
IP_ADDRESS=$(ip route get 1 | awk '{print $NF;exit}')
HOSTNAME=$(hostname)
cp /etc/cassandra/default.conf/cassandra.yaml /etc/cassandra/default.conf/cassandra.yaml.backup
cp /etc/cassandra/default.conf/cassandra.yaml ./cassandra.yaml.template
sed -i "s/ - seeds: \"127.0.0.1\"/ - seeds: \"$IP_ADDRESS\"/g" cassandra.yaml.template
sed -i "s/listen_address:.*/listen_address: $IP_ADDRESS/g" cassandra.yaml.template 
sed -i "s/# broadcast_rpc_address:.*/broadcast_rpc_address: $IP_ADDRESS/g" cassandra.yaml.template 
sed -i "s/broadcast_rpc_address:.*/broadcast_rpc_address: $IP_ADDRESS/g" cassandra.yaml.template 
sed -i "s/# commitlog_total_space_in_mb:.*/commitlog_total_space_in_mb: 8192/g" cassandra.yaml.template 
sed -i "s/commitlog_total_space_in_mb:.*/commitlog_total_space_in_mb: 8192/g" cassandra.yaml.template 
sed -i "s/^rpc_address:.*/rpc_address: 0.0.0.0/g" cassandra.yaml.template
sed -i "s/start_rpc:.*/start_rpc: true/g" cassandra.yaml.template
sed -i "s/thrift_framed_transport_size_in_mb:.*/thrift_framed_transport_size_in_mb: 100/g" cassandra.yaml.template
sed -i "s/commitlog_segment_size_in_mb:.*/commitlog_segment_size_in_mb: 192/g" cassandra.yaml.template
sed -i "s/read_request_timeout_in_ms:.*/read_request_timeout_in_ms: 1800000/g" cassandra.yaml.template
sed -i "s/range_request_timeout_in_ms:.*/range_request_timeout_in_ms: 1800000/g" cassandra.yaml.template
sed -i "s/write_request_timeout_in_ms:.*/write_request_timeout_in_ms: 1800000/g" cassandra.yaml.template
sed -i "s/cas_contention_timeout_in_ms:.*/cas_contention_timeout_in_ms: 1000/g" cassandra.yaml.template
sed -i "s/truncate_request_timeout_in_ms:.*/truncate_request_timeout_in_ms: 1800000/g" cassandra.yaml.template
sed -i "s/request_timeout_in_ms:.*/request_timeout_in_ms: 1800000/g" cassandra.yaml.template
sed -i "s/batch_size_warn_threshold_in_kb:.*/batch_size_warn_threshold_in_kb: 3000/g" cassandra.yaml.template
sed -i "s/batch_size_fail_threshold_in_kb:.*/batch_size_fail_threshold_in_kb: 5000/g" cassandra.yaml.template
sed -i '/data_file_directories:.*/!b;n;c\ \ \ \ - \/data\/data' cassandra.yaml.template  
sed -i "s/hints_directory:.*/hints_directory: \/data\/hints/g" cassandra.yaml.template 
sed -i "s/commitlog_directory:.*/commitlog_directory: \/logs\/commitlog/g" cassandra.yaml.template 
sed -i "s/saved_caches_directory:.*/saved_caches_directory: \/data\/saved_caches/g" cassandra.yaml.template 
\cp -fR ./cassandra.yaml.template /etc/cassandra/default.conf/cassandra.yaml 
# Apply fix to systemd vulnerability preventing service control of cassandra
cat << EOF > /etc/systemd/system/cassandra.service
[Unit]
Description=Apache Cassandra
After=network.target

[Service]
PIDFile=/var/run/cassandra/cassandra.pid
User=cassandra
Group=cassandra
ExecStart=/usr/sbin/cassandra -f -p /var/run/cassandra/cassandra.pid
Restart=always
LimitNOFILE=100000
LimitMEMLOCK=infinity
LimitNPROC=32768
[Install]
WantedBy=multi-user.target
EOF
chkconfig --del cassandra
systemctl daemon-reload
systemctl enable cassandra


Now, proceed to edit /etc/cassandra/default.conf/cassandra.yaml

      sudo nano /etc/cassandra/default.conf/cassandra.yaml


Note:  The script above makes all of the changes to the configuration files stated below.  However, please verify that all of them have been

The first items we will be editing relate to the IP address of the Cassandra node and communications settings.  In our diagram above, this IP address is 192.168.130.10.  You will need to search for 3 keys in the configuration file and modify them accordingly.  The seeds parameter is a comma-delimited list containing all of the seeds in the Cassandra cluster.  Since our cluster consists of only the single node, it contains only one entry - our IP address.  The other 2 parameters contain the IP address on which Cassandra listens for connections and the IP address to broadcast to other Cassandra nodes in the cluster.  The broadcast_rpc_address may be commented out using a # character.  If so, remove the "#" and make sure there are no leading spaces.

Additionally, we need to set rpc_address to 0.0.0.0 (meaning, it will listen to rpc requests on all interfaces), and start_rpc to true (so it will process rpc requests).

  • seeds: "192.168.130.10"
  • listen_address: 192.168.130.10
  • broadcast_rpc_address: 192.168.130.10
  • rpc_address: 0.0.0.0
  • start_rpc: true

The next set of parameters control thresholds to ensure that the data being sent is processed properly.

  • thrift_framed_transport_size_in_mb: 100
  • commitlog_segment_size_in_mb: 192
  • read_request_timeout_in_ms: 1800000
  • range_request_timeout_in_ms: 1800000
  • write_request_timeout_in_ms: 1800000
  • cas_contention_timeout_in_ms: 1000
  • truncate_request_timeout_in_ms: 1800000
  • request_timeout_in_ms: 1800000
  • batch_size_warn_threshold_in_kb: 3000
  • batch_size_fail_threshold_in_kb: 5000

If you have installed your commit log in its own partition, the default commit log size will be the lesser of ¼ of the partition size or 8GB.  In order to ensure that the recommended 8GB is used, you must uncomment the commitlog_total_space_in_mb, such that it will show as below. However, if you are uncommenting this value, please ensure that the partition has enough space to accommodate an 8GB commit log.

  • commitlog_total_space_in_mb: 8192  

The next step is to point the data to the new locations. There are 4 entries which will be modified: data_file_directories, commitlog_directory, hints_directory, and saved_caches_directory.  Search for these keys and edit them as follows:

  • data_file_directories:
    - /data/data
  • commitlog_directory: /logs/commitlog
  • hints_directory: /data/hints
  • saved_caches_directory: /data/saved_caches

After you have made these changes, save the cassandra.yaml file.  Now, start the related services, as follows:

       systemctl start cassandra

Now, proceed to check if Cassandra is running.  To do this, issue the following command: 

      nodetool status

If the service is running, you will receive output such as below:

Datacenter: datacenter1
=======================
Status=Up/Down
|/ State=Normal/Leaving/Joining/Moving
--  Address    Load       Tokens   Owns (effective)  Host ID                               Rack
UN  127.0.0.1  128.4 KB   256      100.0%            ea3f99eb-c4ad-4d13-95a1-80aec71b750f  rack1

If the service is fully operational, the first 2 characters on the last line will state "UN", indicating the node's status is Up, and its state is Normal.  

Tuning Linux for Cassandra Performance

There are multiple tunings which can be performed on Linux to improve the performance of Cassandra.  The first step is to configure the TCP settings by adding the following tuning parameters to /etc/sysctl.conf file:

  • net.ipv4.tcp_keepalive_time=60
  • net.ipv4.tcp_keepalive_probes=3
  • net.ipv4.tcp_keepalive_intvl=10
  • net.core.rmem_max=16777216
  • net.core.wmem_max=16777216
  • net.core.rmem_default=16777216
  • net.core.wmem_default=16777216
  • net.core.optmem_max=40960
  • net.core.somaxconn=4096
  • net.ipv4.tcp_rmem=4096 87380 16777216
  • net.ipv4.tcp_wmem=4096 65536 16777216
  • vm.max_map_count=1048575


To apply the setting without requiring a reboot issue the command:


# sysctl -p


For a full list of steps to take to tune Linux, go to:

https://docs.datastax.com/en/dse/5.1/dse-admin/datastax_enterprise/config/configRecommendedSettings.html

Installing Teamwork Cloud

Initial Installation

The deployment script for TWCloud (install_twc19sp3_centos7.sh) creates a twcloud user, under which the service will run, and downloads all of the necessary files and executes the installer. 

install_twc19sp3_centos7.sh
#!/bin/bash
DOWNLOAD_URL='http://download1.nomagic.com/twcloud190sp3/twcloud_190_sp3_installer_linux64.bin'
INSTALLER='twcloud_190_sp3_installer_linux64.bin'
PRODUCT='Teamwork Cloud 19.0 SP3'
echo "=========================================="
echo "Installing $PRODUCT"
echo "=========================================="
echo "Installing unzip"
yum install -y unzip
echo "Installing fonts"
yum install -y dejavu-serif-fonts
echo "Creating twcloud group and user"
getent group twcloud >/dev/null || groupadd -r twcloud
getent passwd twcloud >/dev/null || useradd -d /home/twcloud -g twcloud -m -r twcloud
chmod -R 777 /home/twcloud/
IATEMPDIR=$(pwd)/_tmp
export IATEMPDIR
mkdir $IATEMPDIR
chmod 777 $IATEMPDIR
echo ""
echo "IMPORTANT: "
echo "           When prompted for user to run service, use twcloud"
echo ""
read -p -"Press any key to continue ...: " -n1 -s
wget $DOWNLOAD_URL
chmod +x $INSTALLER
./$INSTALLER
chown -R twcloud:twcloud /opt/local/TeamworkCloud/
chown -R twcloud:twcloud /home/twcloud/
IP_ADDRESS=$(ip route get 1 | awk '{print $NF;exit}') 
sed -i "s/\"localhost\"/\"$IP_ADDRESS\"/" /opt/local/TeamworkCloud/configuration/application.conf 
sed -i "s/localhost/$IP_ADDRESS/" /opt/local/TeamworkCloud/AuthServer/config/authserver.properties 
echo "======================="
echo "Configuring firewall"
echo "======================="
FWZONE=$(firewall-cmd --get-default-zone)
echo "Discovered firewall zone $FWZONE"
cat <<EOF > /etc/firewalld/services/twcloud.xml
<?xml version="1.0" encoding="utf-8"?>
<service version="1.0">
    <short>twcloud</short>
    <description>twcloud</description>
    <port port="8111" protocol="tcp"/>
    <port port="3579" protocol="tcp"/>
    <port port="10002" protocol="tcp"/>
	<port port="8555" protocol="tcp"/>
	<port port="2552" protocol="tcp"/>
	<port port="2468" protocol="tcp"/>
	<port port="8443" protocol="tcp"/>
</service>
EOF
sleep 30
firewall-cmd --zone=$FWZONE --remove-port=8111/tcp --permanent &> /dev/null 
firewall-cmd --zone=$FWZONE --remove-port=3579/tcp --permanent &> /dev/null 
firewall-cmd --zone=$FWZONE --remove-port=8555/tcp --permanent &> /dev/null 
firewall-cmd --zone=$FWZONE --remove-port=2552/tcp --permanent &> /dev/null 
firewall-cmd --zone=$FWZONE --remove-port=2468/tcp --permanent &> /dev/null 
firewall-cmd --zone=$FWZONE --add-service=twcloud --permanent
firewall-cmd --reload
echo "Increase file limits for twcloud user"
echo "twcloud - nofile 50000 " > /etc/security/limits.d/twcloud.conf
echo "Applying post-install performance tuning"
echo "  /etc/sysctl.conf tuning"
cat <<EOF >> /etc/sysctl.conf

#  Preliminary tunings for Teamwork Cloud
net.ipv4.conf.all.arp_notify = 1
net.ipv4.tcp_keepalive_time=60
net.ipv4.tcp_keepalive_probes=3
net.ipv4.tcp_keepalive_intvl=10
net.ipv4.tcp_mtu_probing=1
net.core.rmem_max=67108864
net.core.wmem_max=67108864
net.core.rmem_default=16777216
net.core.wmem_default=16777216
net.core.optmem_max=40960
net.core.default_qdisc=fq
net.core.somaxconn=4096
net.ipv4.tcp_rmem=4096 87380 33554432
net.ipv4.tcp_wmem=4096 65536 33554432
net.ipv4.tcp_max_syn_backlog=65536
vm.max_map_count = 1048575
vm.swappiness = 0
vm.dirty_background_ratio=5
vm.dirty_ratio=30
EOF
sleep 30
sysctl -p
echo "  ... Creating disk, CPU, and memory tuning parameters in /home/twcloud/tunedisk.sh"
cat << EOF > /home/twcloud/tunedisk.sh
#!/bin/bash
## Added for disk tuning this read-heavy interactive system
sleep 30
#for DISK in sda sdb sdc sdd
for DISK in \$(ls -all /sys/block | egrep 'sd|xvd|dm' | awk '{for(i=1;i<=NF;i++){if(\$i == "->"){print \$(i-1) OFS}}}')
do
	echo \$DISK
	# Select noop scheduler first
    echo noop > /sys/block/\${DISK}/queue/scheduler
	echo scheduler: \$(cat /sys/block/\${DISK}/queue/scheduler)
	echo 1 > /sys/block/\${DISK}/queue/nomerges
	echo nomerges: \$(cat /sys/block/\${DISK}/queue/nomerges)
	echo 8 > /sys/block/\${DISK}/queue/read_ahead_kb
	echo read_ahead_kb: \$(cat /sys/block/\${DISK}/queue/read_ahead_kb)
	echo 0 > /sys/block/\${DISK}/queue/rotational
	echo rotational: \$(cat /sys/block/\${DISK}/queue/rotational)
done 
# Disable huge page defrag
echo never | tee /sys/kernel/mm/transparent_hugepage/defrag

#Disable CPU Freq scaling

for CPUFREQ in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
do
    [ -f \$CPUFREQ ] || continue
    echo -n performance > \$CPUFREQ
done

#Disable zone-reclaim

echo 0 > /proc/sys/vm/zone_reclaim_mode
EOF
sleep 10
chmod +x /home/twcloud/tunedisk.sh
echo "  ... Setting parameters to be executed on server restart"
cat <<EOF >> /etc/rc.local

#  Perform additional tuning for TeamworkCloud
/home/twcloud/tunedisk.sh
EOF
chmod +x /etc/rc.d/rc.local 
echo "  ... Applying tuning changes - there is a 30 second delay before execution"
/home/twcloud/tunedisk.sh 

When you are installing TWCloud


  1. Press ENTER until you will be asked to configure the machine IP.
  2. Configure the machine IP - enter the local IP address of the machine (i.e. 192.168.130.10).
  3. Configure the cluster seed node IP - enter the local IP address of the machine (i.e. 19.168.130.10). 
  4. Configure the TWCloud service owner - enter twcloud
  5. Configure JAVA_HOME - if you are using Oracle Java, using our installation script, you will be prompted with  /opt/local/java/jdk1.8.0_202 - accept this default.  If you are using OpenJDK from the RPM packages, use /etc/alternatives/jre_1.8.0, so that subsequent updates to via yum will not affect the installation.
  6. Choose Install Folder/opt/local/TeamworkCloud


Next, the TWCloud's Pre-Installation Summary will appear. It should look as follows:

===============================================================================
Pre-Installation Summary
------------------------
Please Review the Following Before Continuing:
 
Product Name:
    Teamwork Cloud
 
Install Folder:
    /opt/local/TeamworkCloud
 
Machine ip:
    "192.168.130.10"
 
Seed node ip:
    "192.168.130.10"
 
JAVA_HOME:
    "/opt/local/java/jdk1.8.0_202"
 
Disk Space Information (for Installation Target):
    Required:  395,614,661 Bytes
    Available: 31,608,475,648 Bytes

Note

Anywhere where 192.168.130.10 is displayed, you must replace it with the IP address of your machine.

Post-Install Configuration

The installer has created the preliminary configuration of TWCloud. There are a few more changes, which we must make to the various configurations files in order for TWCloud to be fully functional.

  1. /opt/local/TeamworkCloud/configuration/application.conf - the configuration file for the TWCloud service.

If TWCloud is installed behind a proxy or firewall with NAT, upon the initial connection the MagicDraw client must know the external IP address to which it must connect.  Search for server-broadcast-host, and enter the public IP address instead of the local IP address.

We now need to point TWCloud to the Cassandra database.  Search for seeds =, which is located in the connection section. Edit the value inside the quotes to point to the listen_address you set in cassandra.yaml (i.e. seeds = ["192.168.130.10"])

A default password has been entered in the configuration file for its communication with the authorization server.  It is recommended that it be changed from default.  Search for CHANGE_ME, which is associated with the field pswd, and replace it with a password of your choosing.

2.  /opt/local/TeamworkCloud/AuthServer/config/authserver.properties - the configuration file for Authorization service.

  • server.public.host=public IP address (same as server-broadcast-host in application.conf). If you are accessing the server via a FQDN, use it instead of the IP address.
  • twc.server.host=local IP address
  • cassandra.contactPoints=local IP address
  • If you changed the pswd field in /opt/local/TeamworkCloud/configuration/application.conf from the default, you must modify this file accordingly. Search for authentication.client.secret. Remove the leading # (to uncomment the directive), and replace the CHANGE_ME value with the same value as that in application.conf.
  • If you are accessing the server by FQDN, you must edit the property authentication.redirect.uri.whitelist by adding an entry to whitelist the FQDN.  For example: authentication.redirect.uri.whitelist=https://192.168.130.10:8443/webapp/,https://FQDN:8443/webapp/,https://md_redirect

3.  /opt/local/TeamworkCloud/WebAppPlatform/shared/conf/webappplatform.properties - the configuration file for TWC Admin Console

  • twc.admin.username - Set it to the username of a local account with Administrator privileges (default is Administrator)
  • twc.admin.password - Set it to the password corresponding to the Administrator user (default is Administrator).
  • If you changed the pswd field in /opt/local/TeamworkCloud/configuration/application.conf from the default, you must modify this file accordingly. Search for authentication.client.secret.and replace the CHANGE_ME value with the same value as that in application.conf.

4.  /etc/security/limits.d/twcloud.conf

  • Create /etc/security/limits.d/twcloud.conf to increase the number of open files the process can utilize.  The file contains one line, as below
    twcloud - nofile 50000   

5.  /etc/systemd/system/twcloud.service

  • Add LimitNOFILE=50000, as shown below

ExecStart=/opt/local/TeamworkCloud/scripts/linux/twcloud-run
StandardOutput=journal+console
StandardError=journal+console
SuccessExitStatus=143
LimitNOFILE=50000
[Install]
WantedBy=multi-user.target


To start the authserver service, execute the following command


sudo systemctl start authserver


To start the teamwork cloud service, execute the command


sudo systemctl start twcloud


To start the webapp service, execute the command


sudo systemctl start webapp


To ensure the services start on reboot, execute the following commands


sudo systemctl enable twcloud
sudo systemctl enable authserver
sudo systemctl enable webapp

Additional information which may affect installations in restricted environments

Log Files

TWCloud executes under the twcloud user, and by default will store log files under this user's profile (/home/twcloud).  There are 3 configuration files which control the location of these log files:

/opt/local/TeamworkCloud/configuration/logback.xml

In this file, there are settings for 2 log files which must be edited.

<appender name="SERVER-FILE" class="ch.qos.logback.core.rolling.RollingFileAppender">
                <file>${user.home}/.twcloud/19.0 SP1/server.log</file>
                <rollingPolicy class="ch.qos.logback.core.rolling.FixedWindowRollingPolicy">
                        <fileNamePattern>${user.home}/.twcloud/19.0 SP1/server.%i.log.zip</fileNamePattern>
                        <minIndex>1</minIndex>
                        <maxIndex>1000</maxIndex>
                </rollingPolicy>
 
                <triggeringPolicy class="ch.qos.logback.core.rolling.SizeBasedTriggeringPolicy">
                        <maxFileSize>20MB</maxFileSize>
                </triggeringPolicy>
                <encoder>
                  <pattern>%-5.5level %date{YYYY-MM-dd HH:mm:ss.SSS} %message [%logger{200}, %thread{10}]%n</pattern>
                </encoder>
        </appender>
 
        <appender name="SECURITY-FILE" class="ch.qos.logback.core.rolling.RollingFileAppender">
                <file>${user.home}/.twcloud/19.0 SP1/security.log</file>
                <rollingPolicy class="ch.qos.logback.core.rolling.TimeBasedRollingPolicy">
                <!-- daily rollover -->
                <fileNamePattern>${user.home}/.twcloud/19.0 SP1/security.%d{yyyy-MM-dd}.log</fileNamePattern>
 
                <!-- keep 365 days' worth of history -->
                <!-- maxHistory>365</maxHistory -->
        </rollingPolicy>
                <encoder>
                  <pattern>%-5.5level %date{YYYY-MM-dd HH:mm:ss.SSS} %message [%logger{200}, %thread{10}]%n</pattern>
                </encoder>
        </appender>


In each section, there are 2 settings which must be modified:  file and fileNamePattern. The first setting (file) controls the absolute path to the latest log file.  The second setting (fileNamePattern) controls the naming convention for the archiving of the log files.  In most cases, it will suffice to replace the ${user.home} token with a different location, but you must ensure that the twcloud user has ownership of the target directories.

/opt/local/TeamworkCloud/Authserver/config/logback-spring.xml

This file contains one section which must be modified.

  <appender name="FILE" class="ch.qos.logback.core.rolling.RollingFileAppender">
                <file>${user.home}/.authserver/19.0.SP1/authserver.log</file>
                <rollingPolicy class="ch.qos.logback.core.rolling.FixedWindowRollingPolicy">
                        <fileNamePattern>${user.home}/.authserver/19.0.SP1/authserver.%i.log.zip</fileNamePattern>
                        <minIndex>1</minIndex>
                        <maxIndex>10</maxIndex>
                </rollingPolicy>
 
                <triggeringPolicy class="ch.qos.logback.core.rolling.SizeBasedTriggeringPolicy">
                        <maxFileSize>30MB</maxFileSize>
                </triggeringPolicy>
                <encoder>
                  <pattern>%-5.5level %date{YYYY-MM-dd HH:mm:ss.SSS} %message [%logger{0}, %thread{10}]%n</pattern>
                </encoder>
        </appender>

The same changes and permissions apply to the changes to this file as to those for /opt/local/TeamworkCloud/configuration/logback.xml.

Files installed on system locations

Daemon control filesEnvironment filesCassandra installation
  • /etc/systemd/system/authserver.service
  • /etc/systemd/system/cassandra.service
  • /etc/systemd/system/twcloud.service
  • /etc/systemd/system/webapp.service
  • /etc/cassandra/*
  • /etc/twcloud/*
The script will place the data files in /data/data and commit logs in /logs/commitlog

Frequently Asked Questions

Q:  When accessing https://ip_address:8443/webapp I am displayed with a Tomcat 404 error

A:  This error is typically caused by incorrect credentials for the authentication of webapp. This is accompanied by recurring error messages in web-app.log.

2019-10-12 14:49:14,625 [main] INFO com.nomagic.webappplatform.internal.version.TWCVersionValidator - Waiting for TWC/AuthServer to start, 120 of 120
2019-10-12 14:49:14,626 [main] ERROR com.nomagic.webappplatform.internal.version.TWCVersionValidator - Exception occurred during version checking

 Verify that the credentials are correct in webappplatform.properties

Q:  When Accessing the Teamwork Cloud Admin Console (webapp), I get a system error when redirected to the Authserver login screen

A: This error is typically caused by an omission of the referring URL in the authetication server's whitelist, authentication.redirect.uri.whitelist, located in authserver.properties.

You will see a corresponding error in authserver.log.

ERROR 2019-10-04 17:26:52.258 AuthorizeException: invalid_request, Invalid redirect_uri parameter [AuthorizeController, …]

Update the whitelist to include the referring URL.  A common cause is accessing webapp via a server name of FQDN, when the wyitelist only contains entires for the IP address.

Q:  After entering my credentials in the Authserver login screen, I am not logged in, no error is displayed, and I am presented once again with the login screen

A:  This error is typically caused by a mismatch in the client secret entries - authentication.client.secret located in authserver.properties and webappplatform.properties, and pswd (esi.console.client.pswd) in application.conf.

You will see a corresponding error in authserver.log

ERROR 2019-10-04 17:30:49.382 Invalid client secret …