Validation Rules

Some validation rules guide you in defining your modeling.

Communication

Class	Abbreviation	Message	Severity
Frame	oneSegmentationMax	Only 1 segmentation property per frame	error
	FrameSystemSignalGroup	all the group in same frame	warning
	FrameEndianness	All bus signals in a frame have same value isLittleEndian	error
	FrameMaxTotalSize	Total Size <= Max Max depends of protocol	error
	lengthPositive	length must be >= 0	error
	onePayload	Only 1 payload per Frame	error
	frame_matrix	Frame should be owned by Matrix	warning
	PositiveFrameId	frameId must be >= 0	error
AbstractCANFrame	1 cyclic event	Only 1 cyclic event per frame	error
AbstractCANFrame	1 eventTriggered	Only 1 eventTriggered per Frame	error
CANFrame	frameId range	frameId must be less than 2048 (2.0A) or 536 870 912 (2.0B)	error
	length_less_or_equal_8	CAN Frame length must be <= 8	error
	useless segmentation	useless segmentation length<=8	warning
CANFDFrame	frameId range	frameId must be less than 2048 (2.0A) or 536 870 912 (2.0B)	error
	length_less_or_equals_64	length must be <= 64	error
	useless segmentation	useless segmentation length <= 64	warning
CANXLFrame	extended	A CANXL Frame is never extended	error
	frameId range	priorityId must be less than 2048	error
	length_less_or_equals_2048	length must be <= 2048	error
	useless segmentation	useless segmentation, length <= 2048	warning
J1939Frame	lengthRange	Length above maximum allowed (8 for non segmented Frame, 1785 for segmented Frame)	error
	alwaysExtended	A J1939 Frame is always extended	error
	frameIdRange	frameId must be less than 536 870 912	error
	uselessSegmentation	useless segmentation, length<=8	warning
AbstractFlexRayFrame	lengthRange	length must be <= 254	error
AbstractFlexRayFrame	uselessSegmentation	useless segmentation, length <= 254	warning
FlexRayStaticFrame	slotIdRange	0<= frameId < matrix.numberOfSlots	error
FlexRayDynamicFrame	messageIdRange	matrix.numberOfStaticSlots <= messageId <16384	error
AbstractLINFrame	frameIdRange	frameId must be less than 62	error
	lengthRange	length must be <= 64	error
	uselessSegmentation	useless segmentation, length <= 8	warning
EthernetFrame	lengthRange	length must be between 46 and 1500	error
EthernetFrame	uselessSegmentation	useless segmentation, length <= 1500	warning
BusSignal	-	bitSize must be >= 0	error
	-	bitStart must be >= 0	error
	-	bitSize should be >0	warning
	busSignalType	bus signal's type must be a SystemSignal	error
	busSignal_payload	Bus Signal should be owned by Payload	warning
	Overlapping	Signal overlapping	error
SignalValue	SignalValue_BusSignal	Signal Value should be owned by a Bus Signal or a System Signal	warning
Payload	bs + length	byteStart + length > frame.DLC	error
	byteStartRange	byteStart >= 0	error
	payload_frame	Payload should be owned by Frame	warning

Hardware

Class	Abbreviation	Message	Severity
VirtualLocalAreaNetwork	OnceConnectedSwitchInVLAN	Segments links connected to the switch instance error if only one segment in a vlan	error
	range	priority should be in [0..7]	error
	-	0 and 4095 are reserved vlanId	warning
	range sd_priority	sd_priority should be in [0..7]	warning
	-	0 <= vlanId <= 4095	error
CANBus	-	40000 <= speed <= 20 000 000 bit/s	error
LINBus	-	0 < speed <= 19200 (bit/s)	error
FlexRayBus	-	0 <= speed <= 10000000	error
Connector	ConnectorCompatibleEnds	Check if the two hw ports are compatible (source -> target)	error
Connector	ConnectorMandatoryPorts	Ports are mandatory	error
EthernetPort (occurrence)	MulticonnectedEthernetPort	Ethernet port must be connected by a single ethernet segment	error
CANPort (occurrence)	MulticonnectedCANPort	CAN port must be connected to a single bus	error
LINPort (occurrence)	MulticonnectedLINPort	LIN port must be connected to a single bus	error
CommunicationBus	MultipleConnectionsBusEquipment	Each equipement is only connected once to this bus	warning
Topology	Cycle	no recursion	error

Software

Class	Abbreviation	Message	Severity
SoftwareComposition	Cycle	no recursion	error
AbstractSoftwareVariable	-	direction should be out	warning
AbstractSoftwareVariable	-	type must != null	error
Connector	ConnectorMandatoryPorts	Ports are mandatory	error

System Mapping

Class	Abbreviation	Message	Severity
ItemFlow	conveyed.card	1 Signal per ItemFlow	warning
DirectedFeatures	-	feature direction should be provided	warning

Common

Class	Abbreviation	Message	Severity
Operation	opdir	operation direction should be provided	warning

Content

Space Tools

Communication

Hardware

Software

System Mapping

Common

Content

Space Tools

Breadcrumbs

Validation Rules

Communication

Hardware

Software

System Mapping

Common